Automations
Set up steps that happen by themselves when a visit is booked, closed or missed — send forms or a portal message, add a task, or set a recall — and see each automation's history.
Automations do routine follow-up for you. When a visit is booked, closed or missed, an automation runs up to five steps, each right away or some days later: send a form stack, send a portal message, add a task for a person or group, or set a recall.
For example: after a new patient’s first visit, send a welcome form, add a task to call them in three days, and set a recall for six months.
How to add an automation
- Go to Practice admin › Automations and select Add automation.
- Give it a Name (2–120 characters).
- Choose When:
- A visit is booked
- A visit is closed
- A patient misses a visit
- Under Visit types (none ticked: any), tick the visit types it applies to, or leave all unticked for any type.
- Choose who it’s for: Everyone, New patients (their first visit) or Returning patients.
- Add up to five Steps (described below).
- Select Save. You’ll see Automation added.
The steps
Each step (except a recall) has Days later (0: right away), from 0 to 90 days.
- Send forms: choose a Form stack. The patient gets the forms to fill in.
- Add a task: enter the Task (for example “Call to see how they’re doing”), choose who it’s For (a person or a group), and optionally Due (days after it’s made; blank: no due date).
- Send a portal message: a new message from the practice in the patient’s portal, with a Subject and Message. Choose where Replies go to (a person or a group). The patient is told only “You have a new message”. It’s skipped for patients who aren’t on the portal.
- Set a recall: Return in a number of days, weeks, months or years. Only for A visit is closed. It’s set only if the provider didn’t choose a return at the visit. The provider’s choice always wins.
How to switch an automation on or off
Use the switch beside it in Your automations. An automation that’s off shows Off. Automations are never deleted; switch off the ones you no longer want. Steps that were waiting when you switch one off are skipped.
How to see what an automation did
Each automation shows its last 30 days: how many steps were done, waiting, skipped or couldn’t be done, and who saved it last. Select History to see each step it ran, newest first (the last 200), with the patient, the step and its status:
| Status | Meaning |
|---|---|
| Done | The step happened. |
| Waiting | It’s scheduled for a later day. |
| Skipped | It wasn’t needed or couldn’t apply; the reason is shown. |
| Couldn’t be done | Something went wrong. |
Common reasons a step is skipped:
- The automation was turned off
- The patient record is no longer active
- The appointment is no longer booked
- A return was already set at the visit
- The form stack was archived
- The patient isn’t on the portal
A patient’s own automation steps also show on their chart.
Forms that send themselves
Form stacks can have their own “send automatically” rules, set up in Forms on each stack. They’re listed at the bottom of this page under Forms that send themselves, so you can see everything that runs. Select Open Forms to change them.
Good to know
- Each step runs as the person who last saved the automation. The tasks, forms and messages it creates are recorded under their name, which is shown as Saved by on the automation. If that person leaves the practice, open the automation and save it so the steps run under your name instead.
- Each step is queued once for each visit that matches. Editing an automation doesn’t re-run steps that already ran.
- Only Owners and Practice admins can open this page.
Troubleshooting
| What you see | What it means | What to do |
|---|---|---|
| Give the automation a name. | The name is blank or too short. | Enter a name of at least 2 characters. |
| Add at least one step. | There are no steps. | Add a step. |
| A recall can only be set when a visit is closed. | A recall step is on a booked or missed-visit automation. | Change When to A visit is closed, or remove the recall step. |
| Say what each task is. | A task step has no text. | Fill in the Task. |
| Give each message a subject and its text. | A message step is missing its subject or message. | Fill in both. |
| Couldn’t switch it on: … | Something in the automation is no longer valid, such as an archived form stack. | Edit the automation and fix the step named. |
Related
Still stuck? Contact support and we’ll help. Please don’t include patient information.
Checked against the app on November 14, 2026